Siemens SIMOTICS CONNECT 600 Operating Instructions Manual Download Page 35

Page: 35 / 80

Commissioning

7.1

Setting up the Remote Desktop Connection to the IPC

The IPC is preconfigured so that you can access the IPC via a local service PC using the Microsoft
Remote Desktop Protocol (RDP).

Note

Carefully observe the five safety rules (Page 8) when performing any work.

Note

The preconfigured network settings for interface "X2 P1" of the IPC are required for connection
to the sensor box. Therefore, do not change the network settings for interface "X2 P1" of the IPC.

Note

Protect your local service PC against unauthorized access. Under no circumstance weaken the
hardening measures of the connectivity module:

Preconditions

• The IPC has been mounted, connected up and switched on.

• A local service PC is ready for use.

• The service mode is activated. For more information, see Chapter: Activating/deactivating

the service mode (Page 42).

• A LAN cable is available.

Operating Instructions, 06/2020

Summary of Contents for SIMOTICS CONNECT 600

















































































Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 600, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Brands by name

Popular brands