Siemens SIMOTICS CONNECT 600 Operating Instructions Manual Download Page 30

Page: 30 / 80

①

Miniature circuit breaker

②

LAN interface

③

Connecting terminals for the trip signal (terminals 29 and 30)

④

Cable glands

⑤

Connecting terminal for PE of the power supply

⑥

Connecting terminals for L1 and N of the power supply at the rotary disconnection device

Precondition

• A feeder cable to the 1-phase AC supply:

TN or TT supply system according to VDE 0100 T 300 / IEC 364‑3, with rated voltage
120/230 V AC, 50/60 Hz

• A LAN cable for the connection to the IPC via a dedicated network is available.

• Ethernet connector (that is crimped on)

• Crimping tool

Connecting the power supply

1. Open the sensor box. For the UL version of the connectivity module, follow the instructions

provided in Chapter Only UL version: Opening and closing the sensor box door (Page 25).

2. Open the miniature circuit breaker

①

3. Route the power cable from below through the cable gland into the sensor box.

Connection
6.2 Connecting the sensor box

Operating Instructions, 06/2020

Summary of Contents for SIMOTICS CONNECT 600

















































































Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Related manuals for SIMOTICS CONNECT 600

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 600, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Related manuals for SIMOTICS CONNECT 600

Brands by name

Popular brands