Siemens SIMATIC TDC System Manual Download Page 72 | Manualshive

Page: 72 / 228

background image

Rack

3.3 Rack UR5213 (6DD1682-0CH0)

SIMATIC TDC hardware

72

System Manual, 08/2017, A5E01114865-AL

3.3.8

Ventilation/cooling

The PS5213 power supply is equipped with three fans.
Since the rack is not equipped with an air filter, you should provide a filter on the cabinet if

necessary.

Fan monitoring

The fans are monitored (speed). Activation of the monitoring function is delayed in order to

enable the reliable startup of the rack after you switched on power.
On failure of one or two fans, the power supply is shut down in order to prevent thermal

destruction of the modules. Use the "Shutdown Mode" dip switch to select the mode (the

switch has the “ONE” or “TWO” settings). With switch position “ONE”, a power supply

shutdown is triggered on failure of at least one fan and in switch position “TWO” by the

failure of at least two fans.

WARNING

Always set the “Shutdown mode” dip switch S1.4 to “ONE” for modules requiring forced

convection (e.g. CPU550) at air intake temperatures from 0 C to 55 °C.
You may only set switch position "TWO" if it can be assured that the air intake temperature

at the rack does not exceed 35 °C. The power supply is not shut down on failure of a single

fan, but the corresponding backplane bus signal (FANAL*) is activated and can be detected

by the configuration software.

Fan replacement

At an ambient temperature of 55 °C, it is recommended to replace the fans at intervals of

approx. 40,000 operating hours. The power supply must be removed for fan replacement.

Users cannot replace the fans.

Signaling relay

Three 230V signaling relays with floating potential facilitate external evaluation of the rack's

system states.

Table 3- 5

Signaling relay

Signaling relay Terminal X1 Contact in switched off state Contact in error-free op-

eration

LED in error-free operation

SYSFAIL

1,2

Closed

Closed

Off

POWER

3,4

Open

Closed

green is on

FAN FAIL

5,6

Open

Closed

Off

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
70
71
72
73
74
...
»

Summary of Contents for SIMATIC TDC





































































































































































































































Reviews:

No comments

Related manuals for SIMATIC TDC

Brand: ABB Pages: 370

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: S&C Pages: 40

Brand: S&C Pages: 34

Brand: eclisse Pages: 40

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: Kärcher Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands