Siemens SIMATIC TDC System Manual Download Page 52

Page: 52 / 228

Rack

3.1 Rack UR6021 (6DD1682-0CH3)

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

Output voltages of the power supply

Rated output voltage

Output current

Total

for the modules

+5 V

120 A

79 A

+3.3 V

60 A

36 A

+12 V

17 A

5 A

-12 V

17 A

5 A

Note
Make sure that you do not exceed a total of 600 W (continuous load at 60 °C). This must be

ensured i your configuration.
The output currents of the individual modules are listed in the respective description.

All outputs are sustained short circuit-proof and do not need a basic load.

Battery

Current load

Approx. 20 µA for the monitoring and
max. 180 µA for the slots 1-21

Relay contacts (X1)

Rated voltage (AC)

230 V (max. 264 V)

Rated current

2 A

NOTICE
Assignment of the contacts
Contacts consisting of combinations of safety extra-low voltage and hazardous voltages are

not permitted.

Dimensions

Number of rack slots

Dimensions W x H x D [mm]

approx. 482.6 x 354.9 x 343

Weight

Approx. 20 kg

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Brands by name

Popular brands