Siemens SIMATIC TDC System Manual Download Page 88

Page: 88 / 228

CPU modules

4.2 CPU module CPU550/CPU551

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

4.2

CPU module CPU550/CPU551

4.2.1

Areas of application

The CPU550/CPU551 processor module can be customized by means of graphic interface

and enables the realization of demanding, highly dynamic automatic control systems.
Use cases include:

●

Roll nip controls

●

Hydraulic positioning functions

●

Strip cooling systems

4.2.2

Using the CPU551 - 6DD1600-0BA3

´Please note the following when using the CPU module CPU551 with the article number

6DD1600-0BA3.

Configuration

Note
Configuration

•

Up to D7-SYS V8.0: To configure the CPU module CPU551 "6DD1600-0BA3" in HW

Config, select the CPU551 "6DD1600-0BA2".

•

For system and communications configuration, select SIMATIC D7-SYS as of V5.2.

•

Only use memory cards whose configuration was created with SIMATIC D7-SYS as of

V5.2.

Operation with CP53M0

Note
CPU551 with CP53M0
To operate the CPU module CPU551 (6DD1600-0BA3) with the communications module

CP53M0, use only a communications module CP53M0 with a functional status > 5.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands