Siemens SIMATIC TDC System Manual Download Page 217

Page: 217 / 228

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

217

Submodules

8.1

Program memory modules CPU555

Article number

Program memory (2 MB)

6ES7953-8LL31-0AA0

Program memory (4 MB)

6ES7953-8LM31-0AA0

Program memory (8 MB)

6ES7953-8LP31-0AA0

Description

The program memory modules are used to store the processor program (including the

operating system) you configured in HW Config and CFC and for saving online changes.

Installation/ programming

The program memory module is inserted into the submodule slot X4 provided on the

CPU555 module and can by loaded with the user program in various ways:

●

Offline loading
–

Via a MMC programming adapter installed on the PC

–

Via a SIMATIC USB prommer (6ES7792-0AA00-0XA0) connecte via USB to the PC

●

Online download
–

Directly from the PC via a communication link (e.g. PROFINET) into the memory

module plugged into the CPU555 module.

Program size

The volume of configuration data to download to the memory module (compressed to

approx. 50 %) and the free program memory space can be viewed in the CFC by selecting:
PLC / Load / Info

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands