Siemens SIMATIC TDC System Manual Download Page 17

Page: 17 / 228

Installation and EMC guidelines

1.6 Low-voltage directive

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

1.6

Low-voltage directive

The products listed in the table below fulfill the requirements of EU directive 2006/95/EC,

"Low-voltage Directive". Compliance with this EC directive was tested in accordance with

DIN 61131-2 (corresponds to IEC 61131-2).
The following components are also affected in SIMATIC TDC:

Name

Article number

UR5213

6DD 1682-0CH0

PS5213

6DD 1683-0CH0

UR5213

6DD 1682-0CH2

UR6021

6DD 1682-0CH3

SB 60

6DD 1681-0AF4

SB 70

6DD 1681-0AG2

Fan tray

6DD1683-0CH3

These components are compliant with requirements of the Low-voltage Directive.

1.7

Machinery directive

In accordance with the Machinery Directive 2006/42/EC, it must be ensured that a failure or

malfunction of SIMATIC TDC will not trigger a hazardous state of the machine/plant. This

must always be taken into account when configuring the machine/system.
The system may not be commissioned until it has been proven that the final product is in

compliance with the directive.

Expert personnel

Only expert personnel may configure, commission, service and operate SIMATIC TDC.

Input of external voltages

An external voltage source (e.g. pulse encoder) that is connected to SIMATIC TDC module

inputs must be shut down simultaneously with the shutdown or failure of the SIMATIC TDC

power supply.

1.8

Installation

SIMATIC TDC components are considered open equipment that must be installed in metallic

enclosures containing shielding and equipotential busbars in compliance with the

requirements of IEC 61131-2 (11.1.2; mechanical strength, flame resistance, stability and

shock protection are significant here).

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands