Siemens SIMATIC TDC System Manual Download Page 99 | Manualshive

Page: 99 / 228

background image

CPU modules

4.2 CPU module CPU550/CPU551

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

99

Programming

The user program executed on the CPU module is configured on a PC using

STEP7/HWConfig and CFC and then downloaded to program memory.
The program memory must be located in the CPU module slot provided.
There are two ways of loading the user program:

●

Offline loading
Carried out on the PC using an integrated or external PCMCIA programming adapter

("PC card").

●

Online download
Direct user program download from the PC to program memory in the CPU module via

serial service interface.

User program size

The size of the user program (compressed to approx. 50 %) that was downloaded to

program memory and the size of free program memory can be viewed in the CFC by

selecting the following menu command:

●

PLC / Load / Info

Utilization

Average load (measured with block PSL) should not exceed 95 %, since this may lead to

sporadic overload.

Program memory

The user program created in CFC is downloaded to program memory. Program memory is

realized with Flash EPROM (2, 4 or 8 MB) and 8 KB EEPROM cache memory.
The following program memory may be used optionally, depending on the size of the user

program:

●

MC500 (4 MB)

●

MC510 (8 MB)

●

MC521 (2 MB)

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
97
98
99
100
101
...
»

Summary of Contents for SIMATIC TDC





































































































































































































































Reviews:

No comments

Related manuals for SIMATIC TDC

Brand: K&K Pages: 6

Brand: Waterway Pages: 16

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: RadioMaster Pages: 49

SUPERREMOTE UR19A

Brand: X10 Pages: 3

Brand: Xantech Pages: 102

Brand: Xantech Pages: 17

Brand: X10 Pages: 2

Brand: LLURIA Pages: 2

Brand: Voltech Pages: 8

Brand: Measurement Computing Pages: 32

Brand: Audioaccess Pages: 2

Brand: Apex Toys Pages: 7

Brand: D+H Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands