Siemens SIMATIC TDC System Manual Download Page 57

Page: 57 / 228

Rack

3.2 Rack UR5213 (6DD1682-0CH2)

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

3.2.6

Wiring diagram

Function

Screw terminal with screw lock (3*1.5 mm

, stranded

wires dressed with wire end ferrules with insulating

collars)
Make sure that the strain relief is properly mounted.

Line conductor

Neutral conductor

PE/ground conductor

Function

Cage clamp terminal (0.5 mm

–1.5 mm

, stranded

wires dressed with wire end ferrules with insulating

collars)
Make sure that the strain relief is properly mounted.

1, 2

SYSFAIL signaling contact
NC contact

3, 4

POWER signaling contact
NO contact

5, 6

FAN FAIL signaling contact
NO contact

WARNING

The PE/ground conductor must be connected to the power supply. A PE/ground terminal

on the rack is inappropriate. The PE/ground conductor must be green with yellow stripe

(green/yellow).

Ungrounded installation of the rack is not planned.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands