Siemens SIMATIC TDC System Manual Download Page 54

Page: 54 / 228

Rack

3.2 Rack UR5213 (6DD1682-0CH2)

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

3.2

Rack UR5213 (6DD1682-0CH2)

3.2.1

Areas of application

Rack UR5213 with 21 slots forms the mechanical base for SIMATIC TDC and features an

integrated system power supply and integrated system fans. A high-performance 64-bit

backplane bus supports high-speed data exchange between the inserted modules.

3.2.2

Mechanical layout

Figure 3-4

Rack UR5213 (front view)

Power supply

The power supply with integrated fan for forced convection is installed in the rear section of

the rack.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands