manualshive.com logo in svg

Siemens SIMATIC S7-200, System Manual

The Siemens SIMATIC S7-200 System Manual is a comprehensive guide to getting the most out of your S7-200 programmable logic controller. This manual covers programming, installation, and operation of the S7-200, providing step-by-step instructions and helpful tips. Download this manual for free from manualshive.com to unleash the full potential of your S7-200.

Share
Download
background image

 

Open loop motion control 

 

12.6 Subroutines created by the Motion wizard for the Axis of Motion 

S7-200 SMART 
System Manual, V2.3, 07/2017, A5E03822230-AF 

625

 

12.6.4

 

AXISx_GOTO subroutine 

Table 12- 10  AXISx_GOTO 

LAD / FBD 

STL 

Description 

 

CALL AXISx_GOTO, 

START, Pos, Speed, 

Mode, Abort, Done, 

Error, C_Pos, 

C_Speed

 

The AXISx_GOTO subroutine commands the Axis of Motion to go to a 

desired location.  

 

Table 12- 11  Parameters for the AXISx_GOTO subroutine 

Inputs/Outputs 

Data type 

Operands 

START 

BOOL 

I, Q, V, M, SM, S, T, C, L, Power Flow 

Pos, Speed 

DINT, REAL   ID, QD, VD, MD, SMD, SD, LD, AC, *VD, *AC, *LD, Constant 

Mode 

BYTE 

IB, QB, VB, MB, SMB, SB, LB, AC, *VD, *AC, *LD, Constant 

Abort, Done 

BOOL 

I, Q, V, M, SM, S, T, C, L 

Error 

BYTE 

IB, QB, VB, MB, SMB, SB, LB, AC, *VD, *AC, *LD 

C_Pos, C_Speed 

DINT, REAL   ID, QD, VD, MD, SMD, SD, LD, AC, *VD, *AC, *LD 

Turn on the EN bit to enable the subroutine. Ensure that the EN bit stays on until the DONE 

bit signals that the execution of the subroutine has completed. 
Turn on the START parameter to send a GOTO command to the Axis of Motion. For each 

scan when the START parameter is on and the Axis of Motion is not currently busy, the 

subroutine sends a GOTO command to the Axis of Motion. To ensure that only one GOTO 

command is sent, use an edge detection element to pulse the START parameter on. 
The Pos parameter contains a value that signifies either the location to move (for an 

absolute move) or the distance to move (for a relative move). Based upon the units of 

measurement selected, the value is either a number of pulses (DINT) or the engineering 

units (REAL). 
The Speed parameter determines the maximum speed for this movement. Based upon the 

units of measurement, the value is either a number of pulses/second (DINT) or the 

engineering units/second (REAL). 
The Mode parameter selects the type of move: 

●

 

0: Absolute position 

●

 

1: Relative position 

●

 

2: Single-speed, continuous positive rotation 

●

 

3: Single-speed, continuous negative rotation 

The Done parameter turns on when the Axis of Motion completes this subroutine. 

Summary of Contents for SIMATIC S7-200



































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC S7-200

BAB TECHNOLOGIE DUODMX GATEWAY Documentation preview
DUODMX GATEWAY
Brand: BAB TECHNOLOGIE Pages: 52
HID ENTRYPROX User Manual preview
ENTRYPROX
Brand: HID Pages: 38
Miromico LoRaWAN FMLR PicoCell Quick Start Manual preview
LoRaWAN FMLR PicoCell
Brand: Miromico Pages: 8
Cisco DPC3825 Installation Manual preview
DPC3825
Brand: Cisco Pages: 4
SystemAir RS485 User Manual preview
RS485
Brand: SystemAir Pages: 16
NEC MG-SIP Configuration Manual preview
MG-SIP
Brand: NEC Pages: 81
Sony PWS-110MG1 Operation Manual preview
PWS-110MG1
Brand: Sony Pages: 70
Sony PWS-100MG1 Operation Manual preview
PWS-100MG1
Brand: Sony Pages: 76
WRC 1782-JDO User Manual preview
1782-JDO
Brand: WRC Pages: 27
Eaton POW-R-COMMAND 1000 Quick Start Manual preview
POW-R-COMMAND 1000
Brand: Eaton Pages: 8
Wildix W01PRI Quick Installation Manual preview
W01PRI
Brand: Wildix Pages: 5
Technicolor MediaAccess TG589vn Setup And User Manual preview
MediaAccess TG589vn
Brand: Technicolor Pages: 106
Nexotek NT-B300 User Manual preview
NT-B300
Brand: Nexotek Pages: 61
Rosemount 1420 Quick Start Manual preview
1420
Brand: Rosemount Pages: 28
Raisecom ISCOM HT803G-WS2 User Manual preview
ISCOM HT803G-WS2
Brand: Raisecom Pages: 16
Raisecom RC953-8FE16E1 User Manual preview
RC953-8FE16E1
Brand: Raisecom Pages: 18
ACT'L eWON2001CD Installation Manual preview
eWON2001CD
Brand: ACT'L Pages: 30
DAINCUBE DGW-CE User Manual preview
DGW-CE
Brand: DAINCUBE Pages: 22

Brands by name

Popular brands

Load more brands