manualshive.com logo in svg

Siemens SIMATIC S7-200, System Manual

The Siemens SIMATIC S7-200 System Manual is a comprehensive guide to getting the most out of your S7-200 programmable logic controller. This manual covers programming, installation, and operation of the S7-200, providing step-by-step instructions and helpful tips. Download this manual for free from manualshive.com to unleash the full potential of your S7-200.

Share
Download
background image

 

Program instructions 

 

7.6 Counters 

S7-200 SMART 
System Manual, V2.3, 07/2017, A5E03822230-AF 

271

 

Reset operation  

The operation of reset shown in the following figure applies to all modes that use the reset 

input. In the figure below, the reset operation is shown with the active state assigned as the 

high level. 
HSC reset 

 

HDEF instruction sets the reset active level and counting rate 
HSC0, HSC2, HSC4, and HSC5 counters have two control bits that are used to configure the 

active state of the reset and to select 1x or 4x counting modes (AB quadrature phase 

counters only). These bits are located in the HSC control byte for the respective counter and 

are only used when the HDEF instruction is executed. These bits are defined in the following 

table. 

 

 

Note 
You must set these two control bits to the desired state before the HDEF instruction is 

executed. Otherwise, the counter takes on the default configuration for the counter mode 

selected. 
Once the HDEF instruction has been executed, you cannot change the counter setup unless 

you first place the CPU in STOP mode. 

 
 

Summary of Contents for SIMATIC S7-200



































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC S7-200

B+B KNX-GSM Gateway Documentation preview
KNX-GSM Gateway
Brand: B+B Pages: 19
Patton SmartNode 5540E Series User Manual preview
SmartNode 5540E Series
Brand: Patton Pages: 77
TANDBERG D13841.08 Administrator'S Manual preview
D13841.08
Brand: TANDBERG Pages: 54
SAGEMCOM Swan F5366s User Manual preview
Swan F5366s
Brand: SAGEMCOM Pages: 60
HMS AB7612 User Manual preview
AB7612
Brand: HMS Pages: 74
Smartenit Harmony P2 Quick Start Manual preview
Harmony P2
Brand: Smartenit Pages: 2
iS5 iSG4F User Manual preview
iSG4F
Brand: iS5 Pages: 184
Radio-tone RT-RoIP2 User Manual preview
RT-RoIP2
Brand: Radio-tone Pages: 12
Odin TeleSystems RTP Bridge User Manual preview
RTP Bridge
Brand: Odin TeleSystems Pages: 36
Datalogic QLM700 Installation Manual preview
QLM700
Brand: Datalogic Pages: 16
Wildix W04FXO Quick Installation Manual preview
W04FXO
Brand: Wildix Pages: 5
Wildix DaySaver Quick Installation Manual preview
DaySaver
Brand: Wildix Pages: 15
Telstra TG797n V3 Getting To Know Manual preview
TG797n V3
Brand: Telstra Pages: 34
TECOM AG-300 Plus2 Operation Manual preview
AG-300 Plus2
Brand: TECOM Pages: 30
Anviz C2 Pro User Manual preview
C2 Pro
Brand: Anviz Pages: 102
OpenVox VS-GW1202-16S Quick Start Manual preview
VS-GW1202-16S
Brand: OpenVox Pages: 6
OpenVox DGW-1004 User Manual preview
DGW-1004
Brand: OpenVox Pages: 56
OpenVox Analog Gateway Series User Manual preview
Analog Gateway Series
Brand: OpenVox Pages: 55

Brands by name

Popular brands

Load more brands