manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Share
Download
Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 98

8-12

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

8.2.4

Contents of DP Standard Part

The first six bytes of the diagnostic message (byte 0 to byte 5) are termed the
DP standard part. They are independent of the DP slave used.

You will find a description of the structure of station status 1 in Table 8-8.
The default setting is 02

H

.

Table 8-8

Structure of station status 1 

Bit

Value

Contents

0

1

DP/ASi link cannot be addressed.

1

1

DP/ASi link not yet ready for data exchange.

2

1

The configuration data sent by the DP master do not correspond to
the configuration of the ASi.

3

1

Slave diagnosis available.

4

1

Requested function not supported by DP/ASi link.

5

1

Implausible response received from DP/ASi link.

6

1

Erroneous parameterization message present.

7

1

DP/ASi link assigned parameters by a DP master other than the DP
master that is just attempting to access the DP/ASi link.

You will find a description of the structure of station status 2 in Table 8-9.
The default setting is 05

H

.

Table 8-9

Structure of station status 2 

Bit

Value

Contents

0

1

New parameters have to be assigned to DP/ASi link.

1

1

Static diagnostics available.

2

1

Reserved

3

1

Response monitoring activated.

4

1

FREEZE mode enabled.

5

1

SYNC mode enabled.

6

0

Reserved

7

0

DP/ASi link de-activated.

DP standard part

Station status 1

Station status 2

Diagnostics and Error Handling

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands