manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Share
Download
Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 119

C-3

Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b

Table C-1

Structure of the DP standard part in parameterization message, continued

Byte(s)

Meaning

Value

6

Group ID

You can place several DP slaves in one group with the
group ID.

1

Refer to Table C-3 for the watchdog time base

The station status defines the operating behavior of the DP/ASi link as a DP
slave. Its behavior towards other DP masters is determined; other aspects to
be determined are whether the SYNC and FREEZE modes and the watchdog
are being used.

Table C-2

Structure of station status in parameterization message 

Bit(s)

Value

Meaning

0 to 2

000

Reserved

3

1

The watchdog for the PROFIBUS-DP is enabled in the
DP/ASi link.

4

1

The DP/ASi link can be operated in FREEZE mode.

5

1

The DP/ASi link can be operated in SYNC mode.

6, 7

00

The slave response time (T

SDR

) is modified. All other

parameters remain as they are.

01

The DP/ASi link is enabled for other PROFIBUS ma-
sters.

10

The DP/ASi link is disabled for other PROFIBUS ma-
sters. All parameters are applied; (exception:
T

SDR

+

0).

11

The DP/ASi link is enabled for other PROFIBUS ma-
sters.

Station status

Parameterization Message

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands