Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 109

Page: 109 / 152

A-1

Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b

Technical Data

The DP/ASi link meets the requirements of the Profibus-DP standard, the ASi
standard and UL, CSA and FM approvals.

The general technical data contain the standards and test values maintained
and met by the S7-300 and the test criteria by which the S7-300 was tested.

SIMATIC products meet the requirements if you observe, during installation
and operation, to the installation guidelines described in the manuals.

In Section

You Will Find

on Page

A.1

Standards and Approvals

A-2

A.2

General Technical Data

A-4

Standards and ap-
provals

What are general
technical data?

Heed installation
guidelines

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Search results

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

Reviews:

Brands by name

Popular brands

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Search results

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

Reviews:

Brands by name

Popular brands