manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Share
Download
Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 24

2-6

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

2.4

Connecting Elements

You connect the elements of the ASi by attaching the modules to the ASi
cable. You do not have to operate the ASi cable for this.

The ASi cable is connected to the DP/ASi link by means of a connector.

In section 2.3, Fig. 2-2, you can see an illustration of an example of a mod-
ule.

You place the ASi cable in the module lower part. By attaching the module
upper part to the lower part, the two contact spikes per core penetrate the
insulation of the ASi cable and establish the contact.

You will find comprehensive installation instructions in the description of the
module that you wish to integrate in the ASi.

Should you wish to use a normal 2-wire cable instead of the ASi cable, con-
nect it to the module in accordance with the manufacturer’s specifications.

Connecting

Penetration tech-
nique

Contacts for 2-wire
cable

ASi Basics

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands