manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Share
Download
Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 58

4-22

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

4.4.6

Adapter Cable (6ES5 755-8CA11)

The adapter cable is required to connect the programmers (with programmer
interface module CP 5410-S5 DOS/ST) or the ET 200 Handheld to the
PROFIBUS-DP.

The programmer or the ET 200 Handheld are required for

Setting the station number

Test and commissioning (not ET 200 Handheld)

Diagnostic functions (not ET 200 Handheld)

The adapter cable has the following characteristics:

Degree of protection: IP 66/IP 67 (refer to installation rules, section 4.1)
only at extremity with IP 66/IP 67 bus connector

can be operated at the following baud rates 
9.6; 19.2; 93.75; 187.5; 500; 1500; 3000; 6000 and 12000 kBd

The 3000, 6000 and 12000 kBd baud rates are possible only in the case of
operation with a suitable DP master – for example, the IM 308-C.

The adapter cable has the following connections:

Bus connector in IP 20 (9-pin connector)

Bus connector in IP 66/IP 67 (12-pin connector)

To connect the programmer, you also require the programmer connecting
cable.

Figure 4-6

Adapter cable

Usage

Characteristics

Connections

Installing and Wiring the DP/ASi Link

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands