manualshive.com logo in svg

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Share
Download
Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 32

3-6

Distributed I/O System DP/ASi Link

EWA 4NEB 710 6055-02b

3.4

Configuration with Several Power Supply Connectors

In configurations with a power supply connector (refer to sections 3.2 and
3.3), the power supply is fed along the bus cable.

This configuration is limited by the following factors:

If the power supply and the PROFIBUS-DP field bus are fed on the same
cable, the following values apply to the length of the bus cable between
the power supply connector and the last slave station connected:

Table 3-2

Length of bus cable when PROFIBUS-DP and power supply 
are fed on the same bus cable

Current Loading

Max. Cable Length

< 1 A

80 m

< 2 A

40 m

< 4 A

20 m

Not more than 4 A may be looped through the power supply connector.
The input power of the ET 200 modules and of the DP/ASi link limits the
number of modules that you can connect.

You make allowance for several power supply connectors per segment.
Fig. 3-5 shows a possible installation for the configuration with several
power supply connectors.

SV

External 

power supply

PROFIBUS-DP

PS-
cntr

PS

External

power supply

PROFIBUS-DP

1

PS-
cntr

1

In this case you can use a 2- or 5-core cable, because the two ”left” con-
nections for ”external power supply” and ”PROFIBUS-DP” are not
bridged.

DP/ASi link

DP/ASi link

DP/ASi link

Figure 3-5

Configuration with several power supply connectors

Constraint for
installation with
one power supply
connector

Remedy

Configuration Options

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands