Siemens SIMATIC Distributed I/O System DP/ASi Link Manual Download Page 139

Page: 139 / 152

Glossary-3

Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b

Distributed I/O devices are I/O units that are not used in the base unit but are
set up on a distributed basis; for example:

ET 200 family

S5-95U with PROFIBUS-DP interface

DP/ASi link

other DP slaves from Siemens or external devices.

Distributed I/O devices are connected to the DP master over the PROFIBUS-
DP bus.

DP stands for ”distributed I/O”.

The DP master is an

active node which communicates with the DP slave

stations according to a defined algorithm and makes data available to the
user. Its behavior conforms to standard EN 50170 Volume 2, PROFIBUS.

DP standard slave

Abbreviation for standard EN 50170 Volume 2, PROFIBUS.

A DP standard slave is a

passive node which behaves in accordance with

standard EN 50170 Volume 2, PROFIBUS.

FREEZE is a control command of the DP master to a group of DP slaves.

Upon receiving the FREEZE control command, the DP slave freezes the cur-
rent state of the inputs and transmits the frozen data periodically to the DP
master.

After every FREEZE control command thereafter, the DP slave freezes the
current state of the inputs again.

The input data are not sent periodically to the DP master by the DP slave
again until the DP master sends an UNFREEZE control command.

The I/O code specifies the assignment of inputs and outputs to the data bits.
The I/O code defines sixteen different input/output combinations.

Distributed I/O
devices

DP master

DP slave

DP standard

DP standard slave

FREEZE

I/O code

Glossary

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

























































































































































Search results

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

Reviews:

Brands by name

Popular brands

Siemens SIMATIC Distributed I/O System DP/ASi Link, Manual

Search results

Summary of Contents for SIMATIC Distributed I/O System DP/ASi Link

Reviews:

Brands by name

Popular brands