manualshive.com logo in svg

Siemens RDG200KN, Basic Documentation, Page: 57 / 150

Share
Download
Siemens RDG200KN Basic Documentation Download Page 57

Functions

Control sequences

4

A6V11545892_en--_a

57 | 150

4.7.2 Application mode

The behavior of the thermostat can be influenced via building automation and

control system (BACS) and bus using command "Application mode".
Cooling, heating or both can be enabled or disabled using this signal. Application

mode is supported in LTE-Mode and S-Mode.
RDG2..KN KNX thermostats support the following commands:

#

Application mode Description

Control sequence

enabled

0 

Auto

The thermostat automatically

changes over between heating

and cooling.

Heating, cooling or both

1 

Heat

The thermostat only allows for

heating.

Heating only

2 

Morning warm-up If "Morning warm-up" is

received, the room is heated

up as fast as possible (as

needed). The thermostat only

allows for heating.

Heating only

3 

Cool

The thermostat only allows for

cooling.

Cooling only

4 

Night purge

Not supported by fan coil

applications.

N/A (= Auto)

5 

Pre-cool

If "Pre-cool" is received, the

room is cooled down as fast

as possible (as needed). The

thermostat only allows for

cooling.

Cooling only

6 

Off

Thermostat does not control

outputs, that is, all outputs go

to off or 0%.

Neither heating nor

cooling

8 

Emergency heat

The thermostat heats as much

as possible. The thermostat

allows only heating.

Heating only

9 

Fan only

All control outputs are set to

0% and only the fan is set to

high speed.
The function is terminated by

any operation on the

thermostat.

Run fan at high speed

With all other commands, the thermostat behaves as if in Auto mode, thus, heating

or cooling by demand.
The heating and cooling states of the thermostat can be monitored with the ACS

tool (diagnostic value "Control sequence"). The last active mode is displayed when

the thermostat is in the dead zone or temperature control is disabled.

With a 2-pipe application, the control sequence state is determined by the

application mode and the state of the heating/cooling changeover signal (via local

sensor or bus), or fixed according to the selected control sequence (P001 =

heating (0)/cooling (1)).

Application mode

ACS
Heating or cooling

Summary of Contents for RDG200KN























































































































































Reviews:

No comments