manualshive.com logo in svg

Siemens RDG200KN, Basic Documentation, Page: 43 / 150

Share
Download
Siemens RDG200KN Basic Documentation Download Page 43

Functions

Additional functions

4

A6V11545892_en--_a

43 | 150

4.6.1 Sensors and changeover functions

The heating/cooling changeover information is received via bus. This is only

possible if the control sequence is set to automatic heating/cooling changeover

(P001 = 2) and no local input (X1, X2, U1) is assigned to this function.

In required information is unavailable (e.g., due to data communication issues,

power failure, etc.), the thermostat operates in the last valid room operating mode

(heating or cooling).

If a cable temperature sensor (LG-Ni1000 or NTC 3k) is connected to X1/X2/U1,

and P150/P153/P155 is set to 2, the water temperature acquired by the

changeover sensor is used to change over from heating to cooling mode, or vice

versa.

●

When the water temperature is above 28 °C (adjustable via P060), the

thermostat changes over to heating mode and remains in heating mode until

the temperature drops below 16 °C (adjustable via P059).

●

When the water temperature is below 16 °C (P059), the thermostat changes

over to cooling mode and remains in cooling mode until the temperature

exceeds 28 °C (P060).

●

If the water temperature is between the 2 changeover points immediately after

power-up (within hysteresis), the thermostat starts in the previous mode.

The water temperature is acquired and the operating state is updated accordingly.

M  Operating mode

Cooling mode

T

w

  Water temperature

Heating mode

The setting range is 5 °C...P060-2 K for P059 and P059+2 K… 40 °C for P060.
When P001 = 2 (H/C changeover auto) is selected, an NTC 3k or LG-Ni1000 cable

temperature sensor for automatic heating/cooling changeover or one external

switch for manual or remote changeover can be used to switch the equipment

between heating and cooling:

Normally open:

Contact open  

⇨

  Heating mode

Contact closed 

⇨

 cooling mode

The sensor or switch can be connected to input terminal X2, X1 or U1 based on

the commissioning of the inputs (P150 (X1), P153 (X2), P155 (U1) = 2).
See also Multifunctional input, digital input [

➙

 92].

Heating/cooling

changeover via bus (KNX)

Heating/cooling

changeover

Automatic heating/cooling

changeover via

changeover sensor

Note
Changeover switch (P150,

P153, P155)

Summary of Contents for RDG200KN























































































































































Reviews:

No comments