manualshive.com logo in svg

Siemens RDG200KN, Basic Documentation, Page: 108 / 150

Share
Download
Siemens RDG200KN Basic Documentation Download Page 108

Functions
Control parameters

4

108 | 150

A6V11545892_en--_a

4.15 Control parameters

To optimize control performance, a number of control parameters can be

readjusted on the thermostat via HMI, commissioning/operating tool, or Siemens

smartphone application PCT Go for Android. These parameters can also be set

during operation without opening the unit.
In the event of a power failure, all control parameter settings are retained.
The control parameters are assigned to 2 levels:

●

Service level, and

●

Expert level, including communications, diagnostics and test

The Service level contains a small set of parameters to set up the thermostat for

the HVAC system and to adjust the user interface. These parameters can be

adjusted any time.
The parameters at the Expert level need careful configuration because they impact

the thermostat’s control performance and functionality.

4.15.1 Parameter setting via local HMI

1. Press both left and right buttons simultaneously for 3 seconds or until the

device beeps if the buzzer is enabled (P030).

Release and within 0.5…4 seconds, press the right button again until P001 is

displayed.

Continue with step 2.

1. Press both left and right buttons simultaneously for 3 seconds or until the

device beeps if the buzzer is enabled (P030).

Release and within 0.5…4 seconds, press the left button again until the

temperature display disappears.

Turn the rotary knob counterclockwise minimum ½ rotation. P050 displays.

Continue with step 2.

2. Select the required parameter by turning the rotary knob.

3. Press   (OK); the current value of the selected parameter begins to flash and

can be changed by turning the rotary knob.

4. Press   (OK) to confirm the adjusted value or press button   (Esc) to cancel

the change.

5. If you want to adjust additional parameters, repeat steps 2…4.

6. Press button   (Esc) to exit parameter setting mode.
The factory setting for the control parameters can be reloaded via P505, by

changing the value to On. Confirm the change by pressing the right button.
8888 is then displayed during reloading and device restarts 4 s later.

If password protection (needs to be done by HVAC installer) is enabled, users
must enter the password to open parameter setting mode. If the password is
mistyped 5 times, the thermostat is locked and the password cannot be entered for
5 minutes. Symbols   and   are displayed.

Adjust parameters

Enter only Service level

Enter Expert level with

Diagnostics and test

Reset parameters

Note:

Summary of Contents for RDG200KN























































































































































Reviews:

No comments