Siemens RDG200KN, Basic Documentation, Page: 116 / 150

Functions
Control parameters
4
116 | 150 A6V11545892_en--_a
Para
meter
Name
Fa
cto
ry
s
et
ting
Ran
ge
RDG2
00
KN
RDG2
60
KN
Dep
en
den
cie
s
Expert level
P365 Fan start delay 0 s 0...360 s ✓ ✓ P350
P366 Fan start, minimum hot water
temperature
30 °C OFF,5…60 °C ✓ ✓ P350
Input
Relay functions
P400
9)
Output Q1 function 0 0 = No function
1 = Switch OFF in Protection
2 = Switch ON in Heat/Cool demand
3 = Switch ON in Heat demand
4 = Switch ON in Cool demand
5 = Heating sequence active
6 = Cooling sequence active
7 = External dehumidifier control
8 = External humidifier control ✓ ✓ P350,
P351
P401
9)
Output Q2 function
P402 Output Q3 function
Controller
P450
Control strategy 0 0 = Temperature (T)
1 = Temperature (T) + Relative humidity
(r.h.)
✓ ✓ ‒
P451 Humidity control strategy 2 1 = With setpoint shift
2 = With setpoint shift + external
equipment (humid / dehum)
✓ ✓ ‒
P461 T setpoint shift (humidity) 3 K -3…3 K ✓ ✓ ‒
Side Features
P500
NFC ON ON = Enabled
OFF = Disabled ✓ ✓ ‒
P501 Service filter OFF OFF, 100…9900 h ✓ ✓ P350
P502 Password OFF ON = Enabled
OFF = Disabled ✓ ✓ ‒
P503 Password 000 000…999 ✓ ✓ ‒
P505 Restore factory setting OFF OFF = Disabled
ON = Reload start ✓ ✓ ‒
System
P900
Device address 3) 255 1…255 ✓ ✓ ‒
P901 Geographical zone (apartment) 4) --- ---(0), 1...126 ✓ ✓ ‒
P902 Geographical zone (room) 3) 1 ---(0), 1...63 ✓ ✓ ‒
P903 Heat distr zone heating coil --- ---(0), 1...31 ✓ ✓ ‒
P904 Refrig distr zone cooling coil
P905 Heat distr zone heating surface
P910 Transformation Precomfort 0 0 = Economy
1 = Comfort ✓ ✓ ‒
Note: Parameter display depends on selected application and function. Appl
means application.
1)
When P201/P203 = 1/3/5, P204 = 3/5, P057 & P058 are visible.
2)
When P150, P153 or P155 = 2 and P001 = 2, P059 & P060 are visible.
3)
When P002 ≠ 2, P102 is visible.
4)
Only available for application 2-pipe/2-stage.
5)
When P201 = 3, P206 is visible; P203 = 3, P207 is visible; P204 = 3, P208 is
visible.
6)
When P201 = 1, P214 is visible; P203 = 1, P215 is visible.
7)
When “H/C changeover” function on X1, X2, U1 is selected, P251 is visible.
8)
When “External temperature limit (AI)” on X1, X2, U1 is selected, P252 is visible.
9)
When application is 4-pipe with 6-port ball valve as changeover and PICV, P400
& P401 are invisible.