manualshive.com logo in svg

Siemens micromaster 410, Operating Instructions Manual, Page: 8 / 84

Share
Download
Siemens micromaster 410 Operating Instructions Manual Download Page 8

Safety Instructions

Issue 04/02

MICROMASTER 410    Operating Instructions

8

6SE6400-5EA00-0BP0

Transport & Storage

WARNING

♦

  Correct transport, storage, erection and mounting, as well as careful

operation and maintenance are essential for proper and safe operation of the
equipment.

CAUTION

♦

  Protect the inverter against physical shocks and vibration during transport and

storage. Also be sure to protect it against water (rainfall) and excessive
temperatures (

see table on page 19

).

Commissioning

WARNINGS

♦

  Work on the device/system by 

unqualified

 personnel or failure to comply with

warnings can result in severe personal injury or serious damage to material.
Only suitably qualified personnel trained in the setup, installation,
commissioning and operation of the product should carry out work on the
device/system.

♦

  Only permanently-wired input power connections are allowed. This equipment

must be grounded (IEC 536 Class 1, NEC and other applicable standards).

♦

  If a Residual Current-operated protective Device (RCD) is to be used, it must

be an RCD type B.

♦

  The following terminals can carry dangerous voltages even if the inverter is

inoperative:
- the power supply terminals L and N.
- the motor terminals U, V, W and the terminals DC+ and DC-.

♦

  This equipment must not be used as an ‘emergency stop mechanism’ 

(see

EN 60204, 9.2.5.4)

CAUTION

The connection of power, motor and control cables to the inverter must be carried
out as shown in Figure 2-10 on page 30, to prevent inductive and capacitive
interference from affecting the correct functioning of the inverter.

Summary of Contents for micromaster 410





















































































Reviews:

No comments