Siemens micromaster 410 Operating Instructions Manual Download Page 55

Page: 55 / 84

Issue 04/02

5 System Parameters

MICROMASTER 410 Operating Instructions
6SE6400-5EA00-0BP0

Communication (P0004 = 20)

ParNr

ParText

Default

Acc

P0927

Parameter changeable via

CUT

r0964[5]

Firmware version data

P0971

Transfer data from RAM to EEPROM

CUT

P2000

Reference frequency

50.00

P2009[2]

USS normalization

P2010[2]

USS baudrate

CUT

P2011[2]

USS address

CUT

P2012[2]

USS PZD length

CUT

P2013[2]

USS PKW length

127

CUT

P2014[2]

USS telegram off time

r2015[4]

CO: PZD from BOP link (USS)

P2016[4]

CI: PZD to BOP link (USS)

52:0

r2018[4]

CO: PZD from COM link (USS)

P2019[4]

CI: PZD to COM link (USS)

52:0

r2024[2]

USS error-free telegrams

r2025[2]

USS rejected telegrams

r2026[2]

USS character frame error

r2027[2]

USS overrun error

r2028[2]

USS parity error

r2029[2]

USS start not identified

r2030[2]

USS BCC error

r2032

BO: CtrlWrd1 from BOP link (USS)

r2031[2]

USS length error

r2033

BO: CtrlWrd2 from BOP link (USS)

r2036

BO: CtrlWrd1 from COM link (USS)

r2037

BO: CtrlWrd2 from COM link (USS)

Alarms, Faults and Monitoring (P0004 = 21)

ParNr

ParText

Default

Acc

P0952

Total number of faults

r0947[8]

Last fault code

r2110[4]

Warning number

r2114[2]

Run time counter

P2167

Switch-off frequency f_off

1.00

CUT

Summary of Contents for micromaster 410





















































































Search results

Summary of Contents for micromaster 410

Reviews:

Siemens micromaster 410, Operating Instructions Manual, Page: 55 / 84

Search results

Summary of Contents for micromaster 410

Reviews: