manualshive.com logo in svg

Siemens micromaster 410, Operating Instructions Manual, Page: 7 / 84

Share
Download
Siemens micromaster 410 Operating Instructions Manual Download Page 7

Issue 04/02

Safety Instructions

MICROMASTER 410    Operating Instructions
6SE6400-5EA00-0BP0

7

Safety Instructions

The following Warnings, Cautions and Notes are provided for your safety and as a
means of preventing damage to the product or components in the machines
connected. This section lists Warnings, Cautions and Notes, which apply generally
when handling MICROMASTER 410

 

Inverters, classified as 

General

, 

Transport &

Storage

, 

Commissioning

, 

Operation

, 

Repair 

and 

Dismantling & Disposal

.

Specific Warnings, Cautions and Notes

 that apply to particular activities are

listed at the beginning of the relevant chapters and are repeated or supplemented
at critical points throughout these sections.

Please read the information carefully, since it is provided for your personal
safety and will also help prolong the service life of your MICROMASTER 410
Inverter and the equipment you connect to it.

General

WARNING

♦

  This equipment contains dangerous voltages and controls potentially

dangerous rotating mechanical parts. Non-compliance with 

Warnings

 or

failure to follow the instructions contained in this manual can result in loss of
life, severe personal injury or serious damage to property.

♦

  Only suitable qualified personnel should work on this equipment, and only

after becoming familiar with all safety notices, installation, operation and
maintenance procedures contained in this manual. The successful and safe
operation of this equipment is dependent upon its proper handling,
installation, operation and maintenance.

♦

  Risk of electric shock. The DC link capacitors remain charged for five minutes

after power has been removed. 

It is not permissible to open the equip-

ment until 5 minutes after the power has been removed.

CAUTION

♦

  Children and the general public must be prevented from accessing or

approaching the equipment!

♦

  This equipment may only be used for the purpose specified by the

manufacturer. Unauthorized modifications and the use of spare parts and
accessories that are not sold or recommended by the manufacturer of the
equipment can cause fires, electric shocks and injuries.

NOTES

♦

  Keep these operating instructions within easy reach of the equipment and

make them available to all users

♦

  Whenever measuring or testing has to be performed on live equipment, the

regulations of Safety Code VBG 4.0 must be observed, in particular §8
“Permissible Deviations when Working on Live Parts”. Suitable electronic
tools should be used.

♦

  Before installing and commissioning, please read these safety instructions

and warnings carefully and all the warning labels attached to the equipment.
Make sure that the warning labels are kept in a legible condition and replace
missing or damaged labels

Summary of Contents for micromaster 410





















































































Reviews:

No comments