Siemens micromaster 410 Operating Instructions Manual Download Page 51

Page: 51 / 84

Issue 04/02

5 System Parameters

MICROMASTER 410 Operating Instructions
6SE6400-5EA00-0BP0

5.3

Parameter List (short form)

Explanatory information on following table:

Default: Factory

setting

Level:

Access level (Acc)

Inverter status (Drive State), indicates the inverter state in which a
parameter can be modified (see P0010).

♦

Commissioning

♦

Run

♦

Ready to run

Quick

Commissioning

♦

Parameter can be modified in the Quick Commissioning state.

♦

Parameter cannot be modified in the Quick Commissioning state.

Always

ParNr

ParText

Default

Acc

r0000

Drive display

P0003

User access level

CUT

P0004

Parameter filter

CUT

P0010

Commissioning parameter filter

Quick Commissioning

ParNr

ParText

Default

Acc

P0100

Europe / North America

P0101

Hidden Switch Setting

P3900

End of quick commissioning

Parameter Reset

ParNr

ParText

Default

Acc

P0970

Factory reset

Inverter Unit (P0004 = 2)

ParNr

ParText

Default

Acc

r0018

Firmware version

r0026

CO: Act. DC-link voltage

r0206

Rated inverter power [kW] / [hp]

r0207

Rated inverter current

r0209

Maximum inverter current

P0210

Supply voltage

230

P0290

Inverter overload reaction

P1800

Pulse frequency

CUT

Summary of Contents for micromaster 410





















































































Search results

Summary of Contents for micromaster 410

Reviews:

Siemens micromaster 410, Operating Instructions Manual, Page: 51 / 84

Search results

Summary of Contents for micromaster 410

Reviews: