manualshive.com logo in svg

Siemens MAGNETOM Skyra fit, Operator'S Manual, Page: 95 / 131

Share
Download
Siemens MAGNETOM Skyra fit Operator'S Manual Download Page 95

Pulse triggering

Description

Pulse triggering uses the patient's pulse to trigger the measurement.
A pulse sensor is connected to the patient's toe or finger. The first
pulse wave (“premature pulse wave”) is used for triggering. This wave
corresponds to the systolic blood pressure.

A number of special sequences support retrospective gating.

Performing

✓

Suitable finger adapter is attached.

1

Ensure that the cable is not bent.

2

Attach the pulse sensor to a finger or on a toe.

3

Ensure that the pulse sensor is attached properly.

The red LED (fault) at the PPU is flashing rapidly?

No analyzable signal is available.

◆

Ensure that the pulse sensor is attached correctly.

✓

The pulse sensor is attached.

◆

Perform the examination. See: 

Software operator manual

4.4

4.4.1

4.4.2

Attaching the pulse sensor

Performing the examination

Physiological imaging

4

MAGNETOM Skyra

fit

 | syngo MR E11

95

Print No. M6-04401.621.02.02.02

Summary of Contents for MAGNETOM Skyra fit




































































































































Reviews:

No comments