manualshive.com logo in svg

Siemens MAGNETOM Skyra fit, Operator'S Manual, Page: 79 / 131

Share
Download
Siemens MAGNETOM Skyra fit Operator'S Manual Download Page 79

1

Release the locking lever by turning it counter-clockwise by 90°.

2

Press lightly against the upper or lower edge of the display to move
the monitor into the desired tilt position.

1

Turn the wheel clockwise to raise the monitor.

2

Turn the wheel counter-clockwise to lower the monitor.

The footswitch is used to start and stop the MR measurement in the
examination room.

(1) Hose

(2) Hose connector

(3) Pushbutton unit

(4) Footswitch Start/Stop

For additional support, labels can be affixed to the footswitches.

Start label

Stop label

MR measurements with the footswitch are only possible for protocols
that were configured for manual start-up. This is the case e.g. for
protocols with MR measurements after administering contrast
medium.

Adjusting the monitor height

Operating the footswitch

Performing the measurement

MR system components

3

MAGNETOM Skyra

fit

 | syngo MR E11

79

Print No. M6-04401.621.02.02.02

Summary of Contents for MAGNETOM Skyra fit




































































































































Reviews:

No comments