Siemens CP 1242-7 GPRS V2 Operating Instructions Manual Download Page 31

Page: 31 / 72

Installation, connecting up, commissioning

4.2 Installing and commissioning the CP

CP 1242-7 V2
Operating Instructions, 05/2014, C79000-G8976-C311-00

Dimensions for installation

Figure 4-1 Dimensions for installation of the S7-1200

Table 4- 1 Dimensions for installation (mm)

S7-1200 devices

Width A

Width B *

CPU

CPU 1211C, CPU 1212C

90 mm

45 mm

CPU 1214C

110 mm

55 mm

Signal modules

8 or 16 digital I/Os

2, 4 or 8 analog I/Os

Thermocouple, 4 or 8 I/Os

RTD, 4 I/Os

45 mm

22.5 mm

16 analog I/Os

RTD, 8 I/Os

70 mm

35 mm

Communications

interfaces

CM 1241 RS-232 and CM 1241 RS-485

30 mm

15 mm

CM 1243-5 (PROFIBUS master)

CM 1242-5 (PROFIBUS slave)

30 mm

15 mm

CP 1242-7 GPRS V2 (GPRS CP)

30 mm

15 mm

* Width B: The distance between the edge of the housing and the center of the hole in the DIN rail mounting clip

DIN rail mounting clips

All CPUs, SMs, CMs and CPs can be installed on the DIN rail in the cabinet. Use the pull-out

DIN rail mounting clips to secure the device to the rail. These mounting clips also lock into

place when they are extended to allow the device to be installed in a switching panel. The

inner dimension of the hole for the DIN rail mounting clips is 4.3 mm.

Summary of Contents for CP 1242-7 GPRS V2









































































Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands

Siemens CP 1242-7 GPRS V2, Operating Instructions Manual

Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands