Siemens CP 1242-7 GPRS V2 Operating Instructions Manual Download Page 28

Page: 28 / 72

Installation, connecting up, commissioning

4.1 Important notes on using the device

CP 1242-7 V2

Operating Instructions, 05/2014, C79000-G8976-C311-00

WARNING

Replacing components
EXPLOSION HAZARD
SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION

2 OR ZONE 2.

WARNING

Requirements for the cabinet/enclosure
When used in hazardous environments corresponding to Class I, Division 2 or Class I,

Zone 2, the device must be installed in a cabinet or a suitable enclosure.

General notices on use in hazardous areas according to ATEX

WARNING

Requirements for the cabinet/enclosure
To comply with EU Directive 94/9 (ATEX95), this enclosure must meet the requirements of

at least IP54 in compliance with EN 60529.

WARNING

Suitable cables for temperatures in excess of 70 °C
If the cable or conduit entry point exceeds 70 °C or the branching point of conductors

exceeds 80 °C, special precautions must be taken. If the device is operated at ambient

temperatures > 50 °C, the permitted temperature range of the selected cable must be

suitable for the temperatures actually measured.

WARNING

Protection against transient voltage surges
Provisions shall be made to prevent the rated voltage from being exceeded by transient

voltage surges of more than 40%. This criterion is fulfilled, if supplies are derived from

SELV (Safety Extra-Low Voltage) only.

Summary of Contents for CP 1242-7 GPRS V2









































































Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands

Siemens CP 1242-7 GPRS V2, Operating Instructions Manual

Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands