background image

 

CP 1242-7 V2 
Operating Instructions, 05/2014, C79000-G8976-C311-00 

9

 

 

Application and properties 

1.1

 

Connecting the S7-1200 to a GSM network 

IP-based WAN communication via GPRS   

Using the CP 1242-7 GPRS V2 communications processor, the S7-1200 SIMATIC controller 

can be connected to GSM networks. The CP 1242-7 GPRS V2 allows WAN communication 

from remote stations with a master station, communication between stations via a master 

station (inter-station communication) and direct communication between stations. 
The CP 1242-7 GPRS V2 supports the following services for communication via the GSM 

network: 

 

GPRS (General Packet Radio Service) 
The packet-oriented service for data transmission "GPRS" is handled via the GSM 

network. 

 

SMS (Short Message Service) 
The CP 1242-7 GPRS V2 can receive and send SMS messages. The communications 

partner can be a mobile phone or an S7-1200. 

The CP 1242-7 GPRS V2 is suitable for use in industry worldwide and supports the following 

frequency bands: 

 

850 MHz 

 

900 MHz 

 

1 800 MHz 

 

1 900 MHz 

In countries in which the CP is approved, you will find this on the Internet on the pages of 

Siemens Automation Customer Support under the following entry ID: 
<TODO> 
On the Internet page, select the "Entry list" tab and the "Certificates" entry type. 

 

 

Note 
No CDMA mode   
The CP is not suitable for GSM networks in which the code multiplex method "Code Division 

Multiple Access" (CDMA) is used. 

 

 

Summary of Contents for CP 1242-7 GPRS V2









































































Reviews: