Siemens CP 1242-7 GPRS V2 Operating Instructions Manual Download Page 66

Page: 66 / 72

Accessories

C.2 TS Gateway

CP 1242-7 V2

Operating Instructions, 05/2014, C79000-G8976-C311-00

What functions does the TeleService gateway provide?

The TeleService gateway has the following functions:

Switching station
The TeleService gateway is a PC in the network that serves as the intermediary between

the engineering station and remote S7 station.
Since a firewall is normally closed for connection requests from the outside, a switching

station between the remote station and the engineering station is required. This switching

station can be a telecontrol server or, if there is no telecontrol server in the configuration,

a TeleService gateway. The switching station directs the messages via a tunnel through

the firewall. This allows access by the engineering station connected to a LAN to the S7-

1200 via a router and via the APN of the network provider.

Configuration of the SMS gateway provider
With the help of TS Gateway, SMS gateway providers are configured that are necessary

for the sending of wake-up SMS messages to the remote S7 stations.

Configuration with TeleService gateway

A TeleService gateway is intended for the following telecontrol systems in which TeleService

is used with GPRS:

Configurations without a telecontrol server
In configurations without a telecontrol server, a TeleService gateway is required for

TeleService via GPRS.

Configurations with telecontrol server
In configurations in which a second path needs to be established for TeleService via

GPRS alongside the telecontrol server, a TeleService gateway can be used.
This can, for example, be the case when certain people, groups or companies should not

operate TeleService via the telecontrol server or when access to the stations for

TeleService needs to be set up independent of the telecontrol server.

Range of performance of a TS Gateway

Number of simultaneous TeleService connections: 1

Note
TS Gateway only for TeleService
TS Gateway is used only for the "TeleService" function via GPRS. No connections to the

remote stations can be monitored and no process data can be transferred.

Main and substitute TeleService gateway

If the requirements for availability are higher, you can install TS Gateway as the main or

substitute gateway. If the connection via the main system cannot be established, you can

Summary of Contents for CP 1242-7 GPRS V2









































































Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands

Siemens CP 1242-7 GPRS V2, Operating Instructions Manual

Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands