Siemens CP 1242-7 GPRS V2 Operating Instructions Manual Download Page 29

Page: 29 / 72

Installation, connecting up, commissioning

4.2 Installing and commissioning the CP

CP 1242-7 V2
Operating Instructions, 05/2014, C79000-G8976-C311-00

Overvoltage protection

NOTICE
Protection of the external power supply
If power is supplied to the module or station over longer power cables or networks, the

coupling in of strong electromagnetic pulses onto the power supply cables is possible. This

can be caused, for example by lightning strikes or switching of higher loads.
The connector of the external power supply is not protected from strong electromagnetic

pulses. To protect it, an external overvoltage protection module is necessary. The

manufacturers of industrial overvoltage protection devices produce suitable modules.

4.2

Installing and commissioning the CP

Prior to installation and commissioning

WARNING

Read the system manual "S7-1200 Programmable Controller"
Prior to installation, connecting up and commissioning, read the relevant sections in the

system manual "S7-1200 Programmable Controller", refer to the documentation in the

Appendix.
When installing and connecting up, keep to the procedures described in the system manual

"S7-1200 Programmable Controller".

Configuration

One requirement for the commissioning of the CP is the completeness of the STEP 7 project

data (see below). You should also read the section "Configuration and programming

(Page 45)".

Inserting the SIM card

Note
Inserting and removing the SIM card
Do not insert or remove the SIM card while the CP is operating.

Prior to installation, insert the SIM card in the CP.

Summary of Contents for CP 1242-7 GPRS V2









































































Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands

Siemens CP 1242-7 GPRS V2, Operating Instructions Manual

Search results

Summary of Contents for CP 1242-7 GPRS V2

Reviews:

Related manuals for CP 1242-7 GPRS V2

Brands by name

Popular brands