Siemens Cerberus PRO FC721 Technical Manual Download Page 100

Page: 100 / 118

Commissioning
Detailed commissioning steps

100 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

10.8.8.2 Switch on zone

1. Select 'Topology' > ↑ 'Detection tree' > 'Area' > ↑ 'Section' > 'Zone' in the main

menu.

2. Press the 'More Options' softkey and select 'Execute commands'.
3. Select the 'On' command.



The yellow 'ISOLATION' LED goes out.



The 'Zone' is switched on.

10.8.9 Restarting the detector line

WARNING

Activation of fire or smoke dampers
If fire or smoke dampers are connected to the FS720 via an input/output module,

they may be activated when the station is switched off or when the station or

detector line is restarted.
● If necessary, block the outputs temporarily [➙ 101] before switching off the

station or restarting the station/detector line.

1. Select 'Main menu' > 'Topology' > 'Hardware tree' > ↑ 'Station' > 'Module' (line

card) > 'Line'.

2. Press the 'More Options' softkey and select 'Execute commands'.
3. Select the 'Restart line' command.



The ↑ detector line is restarted. The following messages are displayed:

'Line starting up'

'Device config.runs'

Start line test
Only test the line and line devices once the following messages have disappeared

from the PMI:
- 'Device config.runs'
- 'System startup completed'

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands