Siemens Cerberus PRO FC721 Technical Manual Download Page 78

Page: 78 / 118

Connectivity and communication with 'Station'
Initializing 'Station'

78 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

9.5 Initializing 'Station'

● Each ↑ 'Station' in a system with several networked 'Stations' must have a

unique address.

● Once a 'Station' has been started for the first time or once the firmware on the

main CPU has been updated, a 'Station' has the address '1'. Networked

'Stations' must therefore all be initialized.

● If two 'Sites' are merged to form one ↑ 'Site', the 'Stations' with the same

addresses in the added 'Site' must each be given a new address.

● The 'Initialize station' procedure issues the 'Station' an address within the 'Site'

according to the configuration in Cerberus-Engineering-Tool.

A ↑ standalone 'Station' does not have to be initialized.

If you use a number of network cards on the PC, observe the information in the

chapter 'IP settings for several network cards' in document A6V10210424. See

chapter 'Applicable documents'.

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands