Siemens Cerberus PRO FC721 Technical Manual Download Page 79

Page: 79 / 118

Connectivity and communication with 'Station'

Initializing 'Station'

79 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

Initialize 'Station'

NOTICE

Connection module (card cage) FCA2006-A1 defective or installed incorrectly
Control panels identified incorrectly, e.g. FC726 identified as FC724.
● Check that the connection module (card cage) FCA2006-A1 is installed

correctly.

NOTICE

Faulty initialization for networked station
During initialization, the station must not be connected to the network or any other

station.

The PC is connected locally to the ↑ 'Station'.

1. Highlight the 'Station' you want to initialize.
2. Select the 'Commissioning' > 'Initialize station' menu item.



The following window is opened:

3. Click on 'Start'.



The 'Set the station to access level 3' window opens.

4. Press <MENU> on the 'Station' and enter a valid PIN.
5. Click on 'OK' in the 'Set access level' window.



The 'Station' is initialized.



The 'Station' is restarted.



After a few minutes, the 'Buzzer' sounds twice.

6. Press <Acknowledge> on the ↑ Person Machine Interface to switch off the

'Buzzer'. Do not perform any more actions on the 'Station' until the 'Buzzer' has

sounded for the second time.

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands