Siemens Cerberus PRO FC721 Technical Manual Download Page 36

Page: 36 / 118

Mounting
Options

36 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

Mounting steps

1. Mount the cable gland (5) with the nut (4) on the flange between the fastening

tabs (3).

2. Plug the serial module (1 or 6) into the corresponding connector (X14 or X19).
3. Secure the serial module to the fastening tabs (4) using the two screws (2).
4. Wire up the serial module with the intended components according to the pin

assignment.

Cable glands do not have to be fitted for wiring inside the housing only.

Pin assignments

The serial modules are connected as follows:
● RS232 module: X3 DTE-HOST
● RS485 module: X2 connector

5.5.2.1 X3 DTE HOST on RS282 module

Designation

Description

← DCD

Data Carrier Detected

← DSR

Data Set Ready

← CTS

Clear To Send

0 V

Ground

← RXD

Received Data

DTR →

Data Terminal Ready

TXD →

Transmitted Data

RTS →

Ready To Send

Admissible cable cross-section: 0.2…1.5 mm²

T Participant with RS232 interface

RTS

TXD

DTR

RXD

0 V

CTS

DSR

DCD

DTE-HOST

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands