Siemens Cerberus PRO FC721 Technical Manual Download Page 51

Page: 51 / 118

Installation

Power supply - mains voltage connection

51 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

Determining the battery type

Determine the battery type on the basis of the calculated battery capacity (see

table).

Designation

Type

Capacitance Order number

Battery (12 V, 7 Ah, VDS)

FA2003-A1

7 Ah

A5Q00019353

Battery (12 V, 12 Ah, VDS)

FA2004-A1

12 Ah

A5Q00019354

Battery (12 V, 17 Ah, VDS)

FA2005-A1

17 Ah

A5Q00019677

Battery (12 V, 26 Ah, VDS)

FA2006-A1

26 Ah

A5Q00019356

Table 2: Permitted batteries

NOTICE

Hardware damage
● Due to CE conformity only UL94-V2 batteries may be used.

Notes

● To achieve the system voltage of 24 V, two batteries must always be

connected in series.

● Batteries are not included in the scope of supply of the stations and must be

ordered separately.

● The battery capacity determines the charging current. The charging current

must be taken into account when calculating the power supply.

● The dimensions of the batteries are needed to determine the housing type.

Restriction of the battery dimensions

● With greater battery capacities, the additional empty housing (Standard) should

be used with a 150 W power supply.

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands