Siemens Cerberus PRO FC721 Technical Manual Download Page 98 | Manualshive

Page: 98 / 118

background image

Commissioning
Detailed commissioning steps

10

98 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

10.8.5 Loading automatically created configuration to the PC

The description in this chapter only applies if a configuration has not yet been

loaded to the 'Station' and if the ↑ BDV was installed at the 'Station' after the

'Station' was started for the first time.

1. Select the 'File' > 'New site' menu item.



The 'Create new site' window opens.

2. Select the 'Upload from station(s)' option field.
3. Click on 'Next'.



The 'Create site by uploading from station(s)' and 'Connect' windows are

opened.

4. In the 'Connect' window, select 'Local connection' and then click on 'OK'.



The configuration is loaded to 'Cerberus-Engineering-Tool'.



The progress is displayed in the 'Create site by uploading from station(s)'

window.



The 'Site properties' window is opened after loading.

5. Change the entries if required and click on 'OK'.



The 'New site confirmation' window opens.

6. Click on 'Yes'.



The 'Site' is opened in Cerberus-Engineering-Tool.

10.8.6 Adapting configuration

Adapt the configuration of the ↑ 'Site' in Cerberus-Engineering-Tool, e.g.:
● Changing customer texts
● Setting the properties and the parameter sets
● Changing allocation of 'Zones' and 'Sections'
● Configuring controls
● Configuring the operating and display units
● Configuring the network

You will find information on configuring an ↑ 'Site' in document A6V10210424.

See chapter 'Applicable documents'.

«
...
96
97
98
99
100
...
»

Summary of Contents for Cerberus PRO FC721























































































































Reviews:

No comments

Related manuals for Cerberus PRO FC721

Brand: K&K Pages: 6

Brand: Accel Pages: 8

Brand: ECKELMANN Pages: 178

Brand: Jandy Pages: 28

Brand: Jands Pages: 6

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 7

FIELDPOINT FP-1600

Brand: National Instruments Pages: 21

FieldPoint FP-1001

Brand: National Instruments Pages: 65

FieldPoint FP-1001

Brand: National Instruments Pages: 19

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 10

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands