Siemens Cerberus PRO FC721 Technical Manual Download Page 103

Page: 103 / 118

Commissioning

Detailed commissioning steps

103 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

10.8.15 Remove the elements

If you have uninstalled an C-NET device for good, the corresponding elements,

e.g. the 'Cerberus-Engineering-Tool' must be removed from the logical structure

trees in Zone. You can search for elements using the 'Find' function.
You will find more information in document A6V10210424. See chapter 'Applicable

documents'.

10.8.16 Testing detectors

The commissioning personnel perform the function test for the ↑ automatic fire

detectors and the 'Manual call points'.

You will find additional information about the individual steps on the specified

pages.

The ↑ detector line has been commissioned.

1. Switch the test mode on. Link [➙ 104]
2. Initiate the detector. Link [➙ 103]
3. Switch normal operation on. Link [➙ 104]
4. Test the logged test activations. Link [➙ 103]

10.8.16.1 Activate the detector

DETECTOR TEST is switched on.

1. Activate all automatic 'Detectors' and 'Manual call points' using the

corresponding tools.

2. Write down the sequence of the test activations.



The ↑ alarm indicator for the activated detector flashes at each test activation.



If an ↑ external alarm indicator is connected and correspondingly configured,

the external alarm indicator also lights up.

You will find information about triggering detectors in document A6V10212047.

See chapter 'Applicable documents'.

10.8.16.2 Testing logged test activations

1. Test the logged test activations. This can be done in two ways:

– ↑ Person Machine Interface: Select 'Event memory' in the main menu.

– Cerberus-Engineering-Tool: Select the 'Commissioning' > 'Upload site

event memory' menu items.

2. Rectify existing errors if necessary, e.g., if the ↑ alarm indicator has not flashed

or no test entries exist.

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands