Siemens Cerberus PRO FC721 Technical Manual Download Page 69

Page: 69 / 118

Structure and function

Connecting external alarm indicators

69 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

7.2.1 Mimic display driver FT2001

The mimic display driver is a parallel LED indication for the system-wide signaling

of events and is connected to the C-NET detector line.
The LED are built in a ground plan panel.

7.3 Connecting external alarm indicators

Some C-NET devices have an output where normally an ↑ external alarm indicator

is connected. The output can, however, also be used for any other controls. The

output for the external alarm indicator is controlled by the fire control panel and is

freely configurable.
Depending on the configuration, the output is activated for the external alarm

indicator if the following is true:
● The connected detector is in ↑ danger level 2 or 3 (together with the internal

alarm indicator).

● The assigned ↑ zone has triggered an alarm or ↑ pre-alarm.
● The assigned control is active.
The following ↑ external alarm indicators are available:
● DJ119x/FDAI9x – external alarm indicators that must be connected to the

detector to be displayed.

● FDCAI221 – addressable alarm indicator that can be assigned to any cause

using a control.

Figure 29: Examples of an external alarm indicator

1 External ↑ AI configured in parallel to the ↑ zone
2 External AI configured in parallel to the internal AI of the connected detector

(e.g. false ceiling)

3 External AI configured in parallel to any other zone (via control)

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands