Siemens 7ML5430 Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 111

Siemens 7ML5430 Operating Instructions Manual Download Page 9

Introduction

1.4 Product compatibility

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

9

1.4

Product compatibility

The following table describes compatibility between document edition, device revision,

engineering system and associated Electronic Device Description (EDD).

Manual edi-

tion

Remarks

Device revision

02/2006

•

Resolved issue that could cause peak to be selected below

the TVT curve.

•

MP&F parameters added to device.

•

Fault system upgraded to use S# codes to match PROFIBUS

products.

•

Increased number of level/volume breakpoints to 32.

•

Improved linearity over ambient temperature.
NOTE: Software revision 3.02 is not backwards compatible

due to hardware compatibility.

Firmware: 3.02
EDD: 3.02.01

08/2004

Corrected issue: P210 and P211 values (or HART values for

URV/LRV) were not being preserved over a power cycle if opera-

tion was set to distance or volume.

Firmware: 1.05
EDD: 1.04

06/2004

First edition

Firmware: 1.04
EDD: 2.00

1.5

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines

and networks. Systems, machines and components should only be connected to the

enterprise network or the internet if and to the extent necessary and with appropriate security

measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. You can find more information about industrial security by visiting:

https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends you apply product updates as soon as available and

always use the latest product versions. Use of product versions that are no longer supported,

and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

https://www.siemens.com/industrialsecurity.

«
...
7
8
9
10
11
...
»

Summary of Contents for 7ML5430
















































































































Reviews:

No comments