Siemens 7ML5430 Operating Instructions Manual Download Page 83

Page: 83 / 111

Technical data

10.6 Approvals

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

10.6

Approvals

Note
Conduit glands
The use of approved watertight conduit hubs/glands is required for Type 4X, Type 6, IP67,

IP68 (outdoor applications).

General

FM/

CSA

, CE, RCM

Radio

Europe (RED), FCC, Industry Canada

Hazardous

Intrinsic safety Europe

ATEX II 1 G Ex ia IIC T4 Ga
06ATEX2354X

International

IECEx SIR 13.0005X Ex ia IIC T4 Ga

US/Canada

FM/CSA

Class I, Div.1, Groups A, B, C, D
Class II, Div.1, Groups E, F, G
Class III T4

Brazil

INMETRO DNV 12.0068X
Ex ia IIC T4 Ga
IP67/IP68 -

40 ºC ≤ Ta ≤ +80 ºC

Non-incendive US

FM
Class I, Div. 2, Groups A, B, C, D T5

Marine

ABS

American Bureau of Shipping

Lloyd's Register of Shipping

FM and CSA connection drawings are available online. See FM and CSA connection

drawings (Page 25) for more information.

Note
Testing
EN 61000-4-3 (CE EMC) testing was conducted on the SITRANS Probe LR while mounted

in a metallic vessel.

Summary of Contents for 7ML5430
















































































































Search results

Summary of Contents for 7ML5430

Reviews:

Siemens 7ML5430, Operating Instructions Manual, Page: 83 / 111

Search results

Summary of Contents for 7ML5430

Reviews: