manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 7 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 7

 

Table of contents 

 

SITRANS Probe LR with mA/HART 
Operating Instructions, 05/2019, A5E32337711-AC 

7

 

A.7 

TVT (Time varying threshold) curves ...................................................................................... 88 

A.8 

Auto false-echo suppression .................................................................................................. 88 

A.9 

Output ..................................................................................................................................... 90 

A.10 

Failsafe ................................................................................................................................... 91 

A.11 

Chemical compatibility ............................................................................................................ 91 

B 

HART communication .............................................................................................................................. 92 
B.1 

HART communication for SITRANS Probe LR ....................................................................... 92 

B.2 

HART electronic device description (EDD) ............................................................................. 92 

B.3 

SIMATIC process device manager (PDM).............................................................................. 92 

B.4 

Maintenance settings (accessible via PDM only) ................................................................... 93 

B.5 

HART version .......................................................................................................................... 93 

B.6 

Burst mode .............................................................................................................................. 93 

C 

Application examples ............................................................................................................................... 94 
C.1 

Application examples introduction .......................................................................................... 94 

C.2 

Example 1: Liquid resin in storage vessel, level measurement .............................................. 94 

C.3 

Example 2: Horizontal vessel with volume measurement ...................................................... 96 

D 

Hazardous area installations .................................................................................................................... 98 
D.1 

Wiring details .......................................................................................................................... 98 

D.2 

FM/CSA .................................................................................................................................. 98 

D.3 

EU equivalency ....................................................................................................................... 99 

D.4 

Loop voltage versus loop resistance .................................................................................... 100 

D.5 

IS safety barrier selection ..................................................................................................... 100 

D.6 

Instructions specific to hazardous area installations (reference European ATEX 

Directive 2014/34/EU Annex II, 1/0/6) .................................................................................. 102 

E 

Certificates and support ......................................................................................................................... 103 
E.1 

Technical support .................................................................................................................. 103 

E.2 

Certificates ............................................................................................................................ 103 

 

Glossary ................................................................................................................................................ 104 

 

Index ...................................................................................................................................................... 109 

 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments