manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 31 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 31

 

Commissioning 

 

6.2 Local commissioning 

SITRANS Probe LR with mA/HART 
Operating Instructions, 05/2019, A5E32337711-AC 

31

 

6.2.6.3

 

Handheld programmer: function keys in RUN mode 

 

Key 

RUN mode 

 

mA output value displayed in auxiliary reading field. 

 

Internal enclosure temperature displayed in auxiliary reading field. 

 

Parameter for auxiliary readings 
Press 

 to display the auxiliary reading field when in RUN mode. 

 

Displays the value representing Echo Confidence (P805). 

 

Toggle between Units and % on reading display. 

 

Initiate and complete PROGRAM mode access. 

 

Distance displayed in auxiliary reading field. 

6.2.6.4

 

Accessing a parameter 

 

 

Note 

•

 

The following instructions apply when using the Handheld Programmer. 

•

 

Do not use the Handheld Programmer at the same time as SIMATIC PDM, or erratic 

operation may result. 

•

 

You do not need to key in initial zeros when entering a parameter number: for example, 

for P005, key in 5. 

 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments