manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 69 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 69

 

Parameter assignment 

 

7.28 Test (P900 to P924) 

SITRANS Probe LR with mA/HART 
Operating Instructions, 05/2019, A5E32337711-AC 

69

 

7.27.5

 

P839 TVT hover level 

Defines (in percent) how high the TVT curve is placed above the profile, relative to the 

largest echo. When SITRANS Probe LR is located in the center of the vessel, lower this 

parameter to prevent multiple echo detections. 

 

Values 

Range 

0 to 100% 

Default 

40 

7.28

 

Test (P900 to P924) 

7.28.1

 

P900 Software revision number 

Displays the software revision level. 

 

Values (view only) 

Range 

0.00 to 99.99 

1 

Main code revision 

2 

Primary boot revision 

3 

Alternative boot revision 

3 

Hardware stack revision 

Default 

Determined by the software revision installed 

7.28.2

 

P901 Memory test 

Press ENTER 

 to activate the test.  

 

Values (view only) 

PASS 

Memory text successful 

F1 

Fail RAM 

F2 

Fail EEPROM 

F3 

Fail FLASH 

7.29

 

Measurement 

7.29.1

 

P911 mA output value (HART/mA only) 

Access this parameter to display the current value of the mA output. 

 

Values (HART) 

Range 

3.6 to 22.6 (mA) 

* 

4 mA in HART fixed current mode 

1.

 

Set P201 to 0 (manual). 

2.

 

Enter a test value. 

 

 

Note 
P201 must be set to 0 to enable the test value to be entered at P911. After the test, restore 

P201 to the previous setting. 

 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments