manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 12 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 12

Safety notes 

 

2.2 Laws and directives 

 

SITRANS Probe LR with mA/HART 

12

 

Operating Instructions, 05/2019, A5E32337711-AC 

2.2.1

 

Industry Canada conformity 

Canada Installations only: Industry Canada (IC) rules 

 

 

NOTICE 
Use on a "no-interference, no-protection" basis 
This device shall be installed and operated in a completely enclosed container to prevent 

RF emission, which otherwise can interfere with aeronautical navigation. Installation shall 

be done by trained installers, in strict compliance with the manufacturer’s instructions. 
The use of this device is on a "no-interference, no-protection" basis: 

•

 

The user shall accept operations of high-powered radar in the same frequency band 

which may interfere with or damage this device. 

•

 

The user is responsible for removing, at the user’s expense, any device found to 

interfere with primary licensing operations. 

 

2.2.2

 

Conformity with European directives 

The CE marking on the device symbolizes the conformity with the following European 

directives: 

 

Electromagnetic compatibil-

ity EMC  

2014/30/EU 

Directive of the European Parliament and of the Council on the 

harmonisation of the laws of the Member States relating to elec-

tromagnetic compatibility 

Low voltage directive LVD  

2014/35/EU 

Directive of the European Parliament and of the Council on the 

harmonisation of the laws of the Member States relating to the 

making available on the market of electrical equipment de-

signed for use within certain voltage limits 

Atmosphère explosible 

ATEX  

2014/34/EU 

Directive of the European Parliament and the Council on the 

harmonisation of the laws of the Member States relating to 

equipment and protective systems intended for use in potential-

ly explosive atmospheres 

RED  

2014/53/EU 

Directive of the European Parliament and of the Council on the 

harmonisation of the laws of the Member States relating to the 

making available on the market of radio equipment and repeal-

ing Directive 1999/5/EC 

The applicable directives can be found in the EC conformity declaration of the specific 

device. 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments