manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 82 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 82

Technical data 

 

10.3 Construction 

 

SITRANS Probe LR with mA/HART 

82

 

Operating Instructions, 05/2019, A5E32337711-AC 

10.3

 

Construction 

 

Process 
connections 

threaded connection 

1.5” NPT, BSP, or G (BS EN ISO 228-1) 

Antenna 

polypropylene rod 

hermetically sealed construction standard 100 mm (4") 

shield for maximum 100 mm (4") nozzle, or optional 

250 mm (10") long shield 

 

 

Note 

•

 

Check the ambient and operating temperatures under Enclosure (below) and Approvals 

(Page 83) for the specific configuration you are about to use or install. 

•

 

Approved dust-tight and water-tight conduit seals are required for outdoor Type 4X, Type 

6, IP67, IP68 locations. 

 

Enclosure 

body construction 

PBT (polybutylene terephthalate) 

lid construction 

hard-coated PEI (polyether imide) 

conduit entry 

2 x M20x1.5 (plastic strain relief) or 2 x 1/2" NPT 

thread 

ingress protection 

Type 4X, Type 6, IP67, IP68 (see note below) 

Weight 

standard model

1)

 

1.97 kg (4.35 lb.) 

1) 

 Unit with 100 mm (4") rod and adaptors 

10.4

 

Operating conditions 

 

Location 

indoor/outdoor 

Altitude 

5000 m (16,404 ft) max. 

Ambient temperature 

−40 to +80 °C (−40 to +176 °F)

 

Relative humidity 

suitable for outdoor 
Type 4X, Type 6, IP67, IP68 enclosure 

Installation category 

I 

Pollution degree 

4 

10.5

 

Process 

 

temperature (at process connection) 

−40 to +80 °C (−40 to +176 °F).

 

pressure (vessel) 

maximum 3 bar, gauge (43.5 psi, gauge) 

 

 

Note 
Device-specific approvals 
Always refer to nameplates on the device for device-specific approvals. 

 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments