manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 101 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 101

 

Hazardous area installations 

 

D.5 IS safety barrier selection 

SITRANS Probe LR with mA/HART 
Operating Instructions, 05/2019, A5E32337711-AC 

101

 

 

 

Note 

•

 

The following list is not complete: there are many safety barriers on the market, which will 

work with the SITRANS Probe LR. 

•

 

The barriers listed below have all been tested and are functionally compatible with the 

SITRANS Probe LR. 

•

 

The barriers listed below are all HART compatible. 

 

PLC Input Modules 

 

Manufacturer 

Part number 

Siemens 

SM331 PCS7 HART Input Module 

Passive shunt diode barriers 

 

 

Note 
A well-regulated supply voltage is required. 

 

Manufacturer 

Part number 

MTL 

787SP+ (Dual channel) 

MTL 

7787P+ (Dual channel) 

Stahl 

9001/01-280-100-10 (Single channel) 

Stahl 

9002/01-280-110-10 (Dual channel) 

Active barriers (repeating barriers) 

 

Manufacturer 

Part number 

MTL 

706 

MTL 

7206 

Stahl 

9001/51-280-110-14 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments